DTC P2455 [MZR-CD (RF Turbo)]

id0102f1841600

DTC P2455

Exhaust gas pressure sensor circuit high input
DETECTION CONDITION
•  The PCM monitors the input voltage from the exhaust gas pressure sensor while the engine is running. If the input voltage from the exhaust gas pressure sensor is more than 4.81 V, the PCM determines that there is a malfunction in the exhaust gas pressure sensor circuit.
Diagnostic support note
•  The MIL illuminates if the PCM detects the above malfunction condition in the first drive cycle.
•  FREEZE FRAME DATA is available.
•  The DTC is stored in the PCM memory.
POSSIBLE CAUSE
•  Exhaust gas pressure sensor malfunction
•  Connector or terminal malfunction
•  Exhaust gas pressure sensor power and signal circuits are shorted to each other.
•  Short to power supply in wiring between exhaust gas pressure sensor terminal B and PCM terminal 81
•  Open circuit in wiring between exhaust gas pressure sensor terminal A and PCM terminal 62
•  PCM malfunction

Diagnostic procedure

STEP

INSPECTION

ACTION
1
VERIFY FREEZE FRAME DATA HAS BEEN RECORDED
•  Has FREEZE FRAME DATA been recorded?
Yes
Go to the next step.
No
Record the FREEZE FRAME DATA on the repair order, then go to the next step.
2
VERIFY RELATED REPAIR INFORMATION AVAILABILITY
•  Verify related Service Information availability.
•  Is any related repair information available?
Yes
Perform repair or diagnosis according to the available Service Information.
•  If the vehicle is not repaired, go to the next step.
No
Go to the next step.
3
VERIFY CURRENT SIGNAL STATUS: IS CONCERN INTERMITTENT OR CONSTANT?
•  Connect the M-MDS to the DLC-2.
•  Clear the DTC from the PCM memory using the M-MDS.
•  Start the engine.
•  Is the same DTC present?
Yes
Go to the next step.
No
Intermittent concern exists.
Perform the “INTERMITTENT CONCERN TROUBLESHOOTING”.
(See INTERMITTENT CONCERN TROUBLESHOOTING [MZR-CD (RF Turbo)].)
4
INSPECT EXHAUST GAS PRESSURE SENSOR CONNECTOR FOR POOR CONNECTION
•  Turn the engine switch off.
•  Inspect for poor connection (such as damaged/pulled-out terminals, corrosion).
•  Is there any malfunction?
Yes
Repair or replace the suspected terminal, go to Step 9.
No
Go to the next step.
5
INSPECT EXHAUST GAS PRESSURE SENSOR SIGNAL CIRCUIT FOR SHORT TO POWER SUPPLY
•  Turn the engine switch to the ON position (Engine off).
•  Measure the voltage between exhaust gas pressure sensor terminal B (wiring harness-side) and body ground
•  Is the voltage more than 4.86 V
Yes
Repair or replace harness for short with each other, go to Step 9.
No
Go to the next step.
6
INSPECT EXHAUST GAS PRESSURE SENSOR
•  Inspect the exhaust gas pressure sensor.
•  Is there any malfunction?
Yes
Replace the exhaust gas pressure sensor, go to Step 9.
(See EXHAUST GAS PRESSURE SENSOR/EXHAUST GAS PRESSURE CORRECTION TEMPERATURE SENSOR REMOVAL/INSTALLATION [MZR-CD (RF Turbo)].)
No
Go to the next step.
7
INSPECT PCM CONNECTOR FOR POOR CONNECTION
•  Turn the engine switch off.
•  Inspect for poor connection (such as damaged/pulled-out terminals, corrosion).
•  Is there any malfunction?
Yes
Repair or replace the suspected terminal, go to Step 9.
No
Go to the next step.
8
INSPECT EXHAUST GAS PRESSURE SENSOR FOR OPEN CIRCUIT
•  Turn the engine switch off.
•  Inspect for continuity between exhaust gas pressure sensor terminal A and PCM terminal 62.
•  Is there continuity?
Yes
Go to the next step.
No
Repair or replace the wiring harness for an open circuit, go to the next step.
9
VERIFY TROUBLESHOOTING OF DTC P2455 COMPLETED
•  Make sure to reconnect all disconnected connectors.
•  Clear the DTC from the PCM memory using the M-MDS.
•  Start the engine.
•  Is the same DTC present?
Yes
Replace the PCM, go to the next step.
(See PCM REMOVAL/INSTALLATION [MZR-CD (RF Turbo)].)
No
Go to the next step.
10
VERIFY AFTER REPAIR PROCEDURE
•  Perform the Repair Verification Drive Mode.
•  Are any DTCs present?
Yes
Go to the applicable DTC inspection.
(See DTC TABLE [MZR-CD (RF Turbo)])
No
Troubleshooting completed.